Skip to content

Posts tagged ‘Computer’

1
十二

[转]机箱前置usb面板接线详细教程

一、机箱前置USB接线的定义:

首先还是了解一下机箱上前置USB各个接线的定义。通常情况下,红线:电源正极(接线上的标识为:+5V或VCC)、白线:负电压数据线(标识为:Data-或USB Port -)、绿线:正电压数据线(标识为:Data+或USB Port +)、黑线:接地(标识为:GROUND或GND)。某些机箱厂商基于其本身的工艺设计要求,信号线的颜色会与上面介绍的不尽相同,而且考虑到与主板接线的方便性、准确性、通用性,有的机箱厂商将USB线做到一个模块上。有的机箱厂商考虑到USB线与主板连接时的通用性,则将信号线进行分散并对每一根信号线作以标识,为了适应很多类型的USB接口(以下介绍)。但无论机箱的USB线如何定义,只要明白主板上前置USB接口的每一根针是如何定义的,就不会将USB线接错!

二、主板USB针脚的定义:
下面再来看一下主板上的USB针脚定义,虽然目前各品牌主板上扩展的USB针脚定义各不相同,但不外乎以下几大类型与接线方法:
第一类:8针型:
该类型的针脚是1999年以前生产的主板所用,不过目前少数P4级(低档)主板也有采用这种类型的针脚。通常接线方法:将红线插入USB针脚1与针脚2,余下接线按Data-、Data +、GROUND顺序分别插入余下USB针脚(见图一),第二种接线方式是与第一组接线正好相反(见图二)。



第二类:9针型:
该类型的USB针脚多为最近新出的主板,多见于支持Pentium 4或Athlon XP芯片组的主板,尤其是支持USB2.0的主板。该类型的USB针脚接线较为统一,可通用于大多数主板。




第三类:10针型:
采用该针脚类型的产品多为采用i815、i815E、i815EP、KT133等芯片组的主板,接法较前两种类型来说要乱得多,总结下来大致有五种接法:






一般来说针脚1就是第一组USB的电源正极,分辨针脚1方法就是看其主板上的标识,有的直接标"1"、有的则是黑色三角或用白粗线条表示。还有就是某些品牌的主板如果两个前置USB同时连接USB设备的话,会出现其中一个不能正常使用的情况,这属于该主板的Bug,两个前置USB单独使用还是正常的。

更详细内容请参考 http://www.inpce.com/Html/jsdll/hard_ot/other_hards/130612740.htm



—–

27
十一

[转]机箱前置音频接线正确连接方法

现市场上各种机箱的前置音频面板接线大概分为4种:标准7线接口、简化7线接口、5线接口、4线接口。对于5线、4线接口的面板,由于制造不符合标准,即使连接以后也不能组成正常的回路,后置无法正常发声的;对于这种面板的接法,由于无法实现前后置音频都能正常发声,这里就不说了。

看看现在市面上,一般机箱音频线的标示:


第一种:16针接口




第二种:10针接口




第三种:8针接口



19
十一

[转]导出、备份Outlook邮件帐户及邮件

引用内容 引用内容

现在我们一般会在Outlook里添加多个邮件账户。如果需要重新安装Office或Windows系统,或者需要将一台机器上的所有这些账户设置信息及邮箱里的邮件转移到另一台机器上,下面的工作就很必要了…… 

  一、Outlook多账户信息的备份

  别忘了,Outlook是Microsoft Office的一部分。在安装完Office 2003后,打开“开始→程序→Microsoft Office→Microsoft Office工具→Microsoft Office 2003用户设置保存向导”,打开“Microsoft Office 2003用户设置保存向导”对话框。单击“下一步”。

  如图1,选择“保存本机的设置”,单击“下一步”,在出现的对话框中选择文件保存的位置和文件名(扩展名为.ops),单击“完成”,系统开始备份Office里所做的各种个性化设置,其中就包括Outlook的多个账户信息以及Office用户配置的注册表信息。有了这些信息,恢复多账户信息已经足够。

二、备份Outlook的邮件及任务、日历等信息

  Outlook将数据存储在邮件应用程序编程接口 (MAPI) 文件夹中。MAPI 文件夹可以存储在硬盘上的称为“个人文件夹 (.pst) 文件”的文件中,使用以下步骤可以备份整个个人文件夹 (.pst) 文件:

  第一步:关闭任何与邮件相关的程序,例如 Outlook、Microsoft Exchange或 Windows Messenger;

  第二步:单击“开始→设置→控制面板”,打开“控制面板”窗口,双击“邮件”图标打开“Outlook属性”对话框,单击“显示配置文件”按钮,如图2;

第三步:单击适当的配置文件,然后单击“属性”按钮;

  第四步:单击“数据文件”按钮,再单击选中要备份的个人文件夹服务;

  小提示

  如果你的配置文件中有一个以上的个人文件夹服务,必须分别备份每组个人文件夹 (.pst) 文件。

  第五步:单击“设置”按钮,记下列出的路径和文件名;

  小提示

  个人文件夹 (.pst) 文件包含 Outlook中存储的所有数据,因此有可能太大。不过,可以通过单击“开始压缩”按钮来减小个人文件夹 (.pst) 文件的大小。

  第六步:关闭所有属性窗口,在“资源管理器”或“我的电脑”中找到刚刚记下的.pst文件并做好备份。

  三、备份其他信息

  如果你已经做了自定义设置并希望通过 Outlook 将这些设置复制到另一台计算机,除了个人文件夹 (.pst) 文件外,还需要在备份中包括以下文件,这些文件一般保存在(C:\Documents Data\Microsoft\Outlook Settings\用户名\Application and>文件夹下:)

  ★Outcmd.dat:该文件存储工具栏与菜单设置;

  ★<配置文件名>.fav:这是你的收藏夹文件,它包含 Outlook 面板的设置;

  ★<配置文件名>.nk2:该文件存储“自动完成”功能所使用的昵称;

  ★Normal.dot:如果你使用 Microsoft Word 作为电子邮件编辑器,则签名会作为自动图文集词条存储在 Normal.dot 文件里;

  ★自定义签名文件的位置:<驱动器:\Documents and Settings\用户名\Application Data\Microsoft\Signatures>;其中,“驱动器”表示安装了 Outlook的驱动器,“用户名”表示当前系统登录的用户名。

  小提示

  每个单独的签名都有自己的文件,其名称与你创建该签名时所使用的名称相同。例如,如果你创建了一个名为MySig的签名,则 Signatures 文件夹中会创建三个以MySig为主文件名的自动签名文件,分别是.htm的超文本标记语言 (HTML)格式、.rtf(Microsoft Outlook RTF 格式 (RTF)和纯文本格式的.txt文件。

—–

18
十一

超强取色工具ColorImpact.v3.1.0.build.222之crack文件

超强取色工具,:)

新3.x版较2.X版本,功能及界面上有了很大的改进.



引用内容 引用内容

Experience the fun of using this interactive color wheel! No more guesswork when you pick colors for your next design project. With a single click you can create color combinations with an impact. Version 3 of the award winning ColorImpact features a completely redesigned user interface with lots of new tools and functions.

Just select the main color, and the visual color wheel instantly displays a selection of perfectly matching colors. Creating a color scheme for your design project has never been easier!

This award winning program is used by thousands of professional designers and hobbyists world wide.


Screenshots
官方下载
单独Crack文件下载
Live-share原版及crack文件下载
—–

16
十一

中文域名的Punycode编码

Punycode, defined in RFC 3492, is the self-proclaimed "bootstring encoding" of Unicode strings into the limited character set permitted in host names. The encoding is used as part of IDNA, which is a system enabling the use of internationalized domain names in all languages that are supported by Unicode, where the burden of translation lies entirely with the user application (a web browser for example).

The encoding is applied separately to each component of a domain name which is not represented solely within the ASCII character set, and a reserved prefix 'xn--' is added to the translated Punycode string. For example, bücher becomes bcher-kva in Punycode, and therefore the domain name bücher.ch would be represented as xn--bcher-kva.ch in IDNA.

Encoding of non-ASCII character insertions as code numbers

Special characters are removed from the string, while at the end a sequence of codes is added, one code for each insertion of a special character; these insertions are done primarily in the order of their Unicode-values, and secondarily in the order in which they occur in the string. The code for each insertion represents the number of possibilities of inserting a special character at the given stage (that is, without regard to characters that will be inserted afterwards), before the actual insertion, where these possible insertions are again ordered primarily according to their Unicode-values, and secondarily according to position. The first possibility, denoted by the code "a", means that character 128 is inserted at the beginning of the string, or, if there has already been an insertion of a special character, that the same character is added again immediately after the previous one.

The described coding is a form of delta encoding. Special characters in a word are usually from the same language, hence often with nearby Unicode values. Thus the numbers to be used are often smaller with this method. In the case of multiple occurrences of a character it also helps that positions are counted from the previous position.

In the case of "bücher", the code "kva" is used for inserting "ü" (character 252) in "bcher". Of all possibilities of inserting a special character somewhere in "bcher", there are potentially the characters 128–251, each in six possible positions, as well as "ü" in front of the "b", which come before the actual insertion of "ü" after the "b", hence 124 × 6 + 1 = 745 possibilities.

Re-encoding of code numbers as ASCII sequences
Punycode uses generalized variable length integers to represent these values. For example, this is how "kva" is used to represent the code number 745:

A number system with little-endian ordering is used which allows variable-length codes without separate delimiters: a digit lower than a threshold value marks that it is the most-significant digit, hence the end of the number. The threshold value depends on the position in the number and also on previous insertions, to increase efficiency. Correspondingly the weights of the digits (like the third digit from the right in ordinary numbers having a weight 100) varies.

In this case a "number system" with 36 "digits" is used, with the case-insensitive 'a' through 'z' equal to the numbers 0 through 25, and '0' through '9' equal to 26 through 35. Thus "kva", corresponds to "10 21 0". The second digit has a weight of 35 instead of 36 because for three-digit numbers the first (least significant) digit is in the range b-9, "a" would mark the end of the number. Therefore "kva" represents the number 10 + 35 × 21 = 745.

For the insertion of a second special character in "bücher", the first possibility is "büücher" with code "bcher-kvaa", the second "bücüher" with code "bcher-kvab", etc. After "bücherü" with code "bcher-kvae" comes "ýbücher" with code "bcher-kvaf", etc.

To make the encoding and decoding algorithms simple, no attempt has been made to prevent some encoded values from encoding inadmissible Unicode values: however, these should be checked for and detected during decoding.

Compare an ASCII 'punycoded' URL http://xn--tdali-d8a8w.lv/ (working) and its full Unicode counterpart that does include Latvian characters with appropriate diacritics: http://tūdaliņ.lv.

Punycode is designed to work across all script systems, and to be self-optimizing by attempting to adapt to the character set ranges within the string as it operates. It is optimized for the case where the string is composed of zero or more ASCII characters and in addition characters from only one other script system, but will cope with any arbitrary Unicode string. Note that for DNS use, the domain name string is assumed to have been normalized using Nameprep and (for top-level domains) filtered against an officially registered language table before being Punycoded, and that the DNS protocol sets limits on the acceptable lengths of the output Punycode string.


在线转码链接:
CNNIC
http://www.motobit.com/util/punycode-decoder-encoder.asp
—–

16
十一

Dreamweaver 9 (Hanzo) 预发行

收到Adobe的邀请函.DW9即将开测……

引用内容 引用内容
告诉您一个振奋人心的消息:您受邀参加专享的 Beta 版测试(现称为预发行)计划,Dreamweaver 9 (Hanzo)。该预发行计划的名称是“Hanzo 预发行”。

请完成所有预发行手续并访问“Hanzo 预发行主页和指南”网站。
…………
…………
请查阅以下有关您参加预发行计划的 *标准* Adobe 策略:

请注意,本邀请函并不保证您将会获准参加预发行计划。

只有在所有注册手续成功完成并签订在线预发行协议之后,您才可以获准参加 Hanzo 预发行计划。

您参加 Hanzo 预发行计划的活动受《系列协议》中规定的“条款和条件”的约束。请仔细阅读《系列协议》,然后签订该协议。



去年参加完MM的DW8测试之后,还收到MM寄过来的4套繁体版的DW8 :)

等过段时间看看是否能成为DW9的内测员….

Weboy
WordPress Themes